Upgrading Your House Window and Door Security, by Happy Hal

My darling wife read the article on Lexan and asked me to contribute the following. My professional specialty lies in the area of windows and doors.

How to Prepare Doors

Replace the short screws (3/4″) in the door lock plates with longer ones minimum 3″ but 4″ would be better. The 3″ are # 8 but the 4″ are #10 almost twice as strong.

There are two each on the strike plate of the depress plunger and two for the deadbolt.
These screws enter the studs making a considerably stronger safety connection than short screws that only penetrate the light weight trim wood in the jam of the typical door unit.

In our area city code requites rental units to provide blind deadbolts (one sided locks) to prevent entry by service personnel while tenant is at home. These can be installed on any exterior entry door. The strike plates should get the longer screws as well.

Stronger security may be obtained by any of several “security accessories.” These center on the use of steel to reinforce the door jams. Lowe’s in our area sells a 14 gauge. jam sleeve that is screwed with 6 to 8 3″ screws into the jam and needs to be installed under the decorative trim. Other steel reinforce systems that wrap the jam or the stud with the same effect. Most of these require some level of professional skill to finish out successfully.

The very minimum upgrade is the double cylinder deadbolt which requires a key on the inside as well as the outside. This prevents a broken window entry from providing 36’x80″ exit. (Some home owners leave an extra key in the lock to expedite normal exit; not a good idea as it defeats the purpose. )

An additional security precaution installs a loud bell on a string that will alert you or a pet of unexpected opening .

Windows – How to Prevent Entry

First preparation lies in the simple process of locking the window lock as a habit. Every window has a lock when new, so use it. If the lock is broken it either may be replaced for free or low cost from the manufacturer. Additionally a turn buckle clamp lock may be purchased for each operative window and installed on the jam in either the closed position or up to 6″ up. This would permit opening of window during comfortable temperature conditions. As cheap alternative In lieu of this, a simple self tap screw (maybe #6 x 1/2″ may be installed in the jam to prevent the window from opening higher than a stated mount, like 6″ up.

Next level of precaution for the windows is to install some type of bars out side the window unit. This also may be installed on the inside of “sky windows’ or skylights.

For people who want a more attractive protection we suggest a clear Lexan or Lexan equivalent covering for each window panel. Lexan Window panels Where cost and budget is an issue start on front and/or rear units as these are the most likely entry points for home intruders.

For single units a box type home improvement store sells clear poly propyl window replacement. These come in 1/8″, 3/16″ or 1/4″ thicknesses. Banks of course use 1″ thick units at the teller window; but you can easily visualize the result: Clear but great protection. Even 1/8″ thickness proves very difficult to penetrate with any thing other than firearms.

For these elements I recommend the thicker panels. The 1/4″ will prevent breakage by .22 caliber rimfire weapons.

Where cost and budgets prevail, the thickness may be mixed with the thicker ones on the front or the rear, and lighter ones on the non exposed views.

Installing Lexan Window Panels

Planning : count the windows and measure the out side and inside measurements for each unit. Typically the outside measurements will be a little larger than the inside. The age of the house will determine the type of window. Houses built prior to the WWII typically will have wood or steel frame windows. The planning for each is similar. We recommend that the Lexan panels be installed by screw or blind steel pop rivet for steel units. Measure the inside of the sash (the part that moves) for the size of the installed Lexan panel. The fastener should be installed out side the glass perimeter and inside the frame. sometimes this space is small but would be large en ought to hold a fastener.

The houses built after this war use more aluminum as the aluminum manufacturing diverted from war effort became a cost effective component for the building explosion that took place after the war effort. These units may have the Lexan installed either on the inside or the outside; or both. The upper unit typically does not operate and the Lexan may be successful installed on the outside. because the lower panel does operate and the Lexan panel should be installed on the inside. Again the fastener (Tec-self tapping screws or blind pop-rivets) needs to be installed out side the perimeter of glass on the frame so the window will still operate but not break the glass. .

Houses newer than this might have some variation of wood, wood covered with vinyl, or solid vinyl window installation. For these units the Lexan panel are better installed on the outside of the frame on the upper and on the inside of the frame on the lower. Some type of extrusion can be made to hold the Lexan on the window and removed at times that operator needs to be opened. Turn buckle tabs also may be used to safely remove the paned. On fixed units the panels may be installed permanently on the outside of the frame.

The purpose of the Lexan panels is to prevent breakage of the glass during lawless events, where breakage of the perimeter glass would provide home invasion routes.

Installation

The Lexan comes in 4’x8′ and 4’x12′ when purchased from the plastics wholesaler.

For simplicity the panels may be numbered from the front door clockwise till all units are included. Where there are multiple panels on the same opening, each may be lettered clockwise or upper then lower. Take the measurements that prescribe the windows and place on 1/4′ graph paper where the scale accurately represents the finished size of the Lexan panel.

cut out the scaled models of the Lexan panels.

On the graph paper outline the outside of 4’x8″ (or 4’x12′ which ever is available). the same scale of the window panels. lay out the cut out panels on the graph paper in the more efficient use of the material. This will tell you how much raw material is needed, and which cut out is best used for each sheet. A person could mix or match the panels for the various windows so that the “best fit” is reached.

After the planning for the whole house is completed the budget becomes clearer and the actual cut out of the material begins. The material can be cut with a triple chip diamond blade, or an masonry abrasive blade. For the abrasive blade, the material should be cut approximately half thickness then the break will be clean and even. Full cut will cause build-up of “melted material.” Such will have to be ground smooth or polished. Although the triple chip will cost more the results will justify the cost. In all cases cold material (<55 deg F.) is more brittle and can easily break in the wrong place. Warm up for minimum of 4 hours.

All that remains is to install each panel of Lexan on the respective window per cut-out models. Suggest a check-off of the models as the material is cut so that the end result complies with the plan.

I hope that some one finds this useful.